The arpeggiator explained: modes, octave range, gate, latch and the settings that matter
Up, down, as-played order, octave range, rate, gate length, latch, swing and ratchets: what each arpeggiator setting does and how to put it to use.

Almost every recent synth, hardware or software, has an arpeggiator. The idea fits in one sentence: you hold a chord, and the machine plays its notes one at a time, in a loop, in tempo. Behind that simplicity, a handful of settings completely change the result. This guide goes through them in the order they appear on most front panels, then offers three recipes to try.
Arpeggiator or step sequencer?
Both produce rhythmic patterns, but not in the same way:
| Arpeggiator | Step sequencer | |
|---|---|---|
| Notes played | the ones you are holding right now | the ones programmed into each step |
| Order | computed by a mode (up, down…) | set by hand, step by step |
| Changing harmony | play a new chord, the pattern follows | transpose or rewrite the sequence |
| Typical use | live playing, improvisation | composed basslines and patterns |
Many instruments blend the two: an arpeggiator that follows a programmed rhythm, or a sequencer transposed in real time from the keyboard.
Mode: in what order
- Up: lowest note to highest, then back to the bottom. The default and the easiest to follow.
- Down: the reverse, top to bottom; darker, with a falling feel.
- Up/Down: there and back. Depending on the instrument, the outer notes are played twice (“inclusive”) or once (“exclusive”), which changes the cycle length and where it lands in the bar.
- As played (or order): notes come out in the order you pressed them. This mode gives the most melodic control.
- Random: a new draw on every step; good for textures, less so for a melody you want to repeat.
- Chord: the whole chord retriggers on each step, turning the arpeggiator into a rhythm generator.
Octave range
The Octave (or Range) setting repeats the pattern over one, two, three or four octaves above the held chord. Three notes over two octaves give a six-step cycle, which rotates against a bar of eight or sixteen sixteenth notes: the origin of many hypnotic patterns. For a cycle that lands back on the beat, play four notes, or two notes over two octaves.
Rate: division and sync
The division sets each note’s length relative to tempo: quarter, eighth, sixteenth (1/16), and their triplet (1/8T, 1/16T) or dotted versions. Sixteenths are the classic value in electronic dance music. The arpeggiator follows the internal clock or an external MIDI clock; on an analogue setup it can also follow a pulse clock, as explained in our guide to CV/Gate and control voltage.
Gate length
The gate is how long each note is held, as a percentage of the step. At 50%, the note lasts half a sixteenth then stops: the pattern is detached and bouncy. At 100%, notes touch; with legato portamento they glide into each other. Gate works hand in hand with the ADSR envelope: a short gate never lets the envelope reach sustain, so only attack and decay are heard.
Latch, swing and ratchets
Latch (or Hold)
Latch keeps the chord going after you let go of the keys. The pattern runs on its own and your hands are free for the filter. A new chord replaces the old one; on some instruments, notes added while a key is still held join the current chord.
Swing
Swing delays every other note. At 50% the grid is straight; around 55 to 60% the pattern gains a more human lilt without sounding lopsided.
Ratchets and rests
Recent arpeggiators borrow sequencer features: ratchets (a note repeated two, three or four times within one step, as a burst), muted steps, or a rhythm pattern that decides which steps play. That is how you break an arpeggio’s regularity without changing its notes.
Three recipes to try
The trance pluck
- Up mode, two octaves, 1/16, 50% gate, latch on.
- Sawtooth oscillator, low-pass filter fairly closed, filter envelope with zero attack and short decay.
- Add a dotted-eighth delay: the repeats fill the gaps in the pattern.
The “Berlin School” sequence
- As-played mode, one octave, 1/16, 80% gate.
- Play four notes with the root first, then slowly open and close the filter by hand or with a very slow LFO.
- Change one note of the chord every four bars to make the line evolve.
The random texture
- Random mode, three octaves, 1/16T (triplets), 30% gate.
- Short, percussive sound, long reverb, panning modulated by an LFO.
- Hold a widely spaced four-note chord (fifths and fourths) to avoid clashes.
What to check when buying
- an as-played mode, the most musical one, missing from some entry-level models;
- MIDI clock in and out, and the option to send the arpeggiated notes to another instrument;
- adjustable gate and swing, often buried in a menu;
- on a polysynth, the ability to arpeggiate while keeping a sustained pad layer (split or multitimbral mode).
For the instrument’s history, the Wikipedia article on the arpeggiator traces its path from organs to 1980s synths. More sequencing guides are collected in our sequencing and arpeggios section.