Updated Featured The arpeggiator explained: modes, octave range, gate, latch and the settings that matter

Sequencing & Arpeggios

The arpeggiator explained: modes, octave range, gate, latch and the settings that matter

Up, down, as-played order, octave range, rate, gate length, latch, swing and ratchets: what each arpeggiator setting does and how to put it to use.

Graphic of vertical burgundy bars rising and falling like a waveform on a pale pink background, in a burgundy frame
Illustration: Synth News (in-house diagram).

Almost every recent synth, hardware or software, has an arpeggiator. The idea fits in one sentence: you hold a chord, and the machine plays its notes one at a time, in a loop, in tempo. Behind that simplicity, a handful of settings completely change the result. This guide goes through them in the order they appear on most front panels, then offers three recipes to try.

Arpeggiator or step sequencer?

Both produce rhythmic patterns, but not in the same way:

ArpeggiatorStep sequencer
Notes playedthe ones you are holding right nowthe ones programmed into each step
Ordercomputed by a mode (up, down…)set by hand, step by step
Changing harmonyplay a new chord, the pattern followstranspose or rewrite the sequence
Typical uselive playing, improvisationcomposed basslines and patterns

Many instruments blend the two: an arpeggiator that follows a programmed rhythm, or a sequencer transposed in real time from the keyboard.

Mode: in what order

Four arpeggiator modes on a C major chord, two octaves Up C3 E3 G3 C4 E4 G4 Down C3 E3 G3 C4 E4 G4 Up/Down C3 E3 G3 C4 E4 G4 As played (G, C, E) C3 E3 G3 C4 E4 G4
Eight arpeggiator steps on a held C-E-G chord, two-octave range, by mode. Diagram: Synth News.
  • Up: lowest note to highest, then back to the bottom. The default and the easiest to follow.
  • Down: the reverse, top to bottom; darker, with a falling feel.
  • Up/Down: there and back. Depending on the instrument, the outer notes are played twice (“inclusive”) or once (“exclusive”), which changes the cycle length and where it lands in the bar.
  • As played (or order): notes come out in the order you pressed them. This mode gives the most melodic control.
  • Random: a new draw on every step; good for textures, less so for a melody you want to repeat.
  • Chord: the whole chord retriggers on each step, turning the arpeggiator into a rhythm generator.

Octave range

The Octave (or Range) setting repeats the pattern over one, two, three or four octaves above the held chord. Three notes over two octaves give a six-step cycle, which rotates against a bar of eight or sixteen sixteenth notes: the origin of many hypnotic patterns. For a cycle that lands back on the beat, play four notes, or two notes over two octaves.

Rate: division and sync

The division sets each note’s length relative to tempo: quarter, eighth, sixteenth (1/16), and their triplet (1/8T, 1/16T) or dotted versions. Sixteenths are the classic value in electronic dance music. The arpeggiator follows the internal clock or an external MIDI clock; on an analogue setup it can also follow a pulse clock, as explained in our guide to CV/Gate and control voltage.

Gate length

The gate is how long each note is held, as a percentage of the step. At 50%, the note lasts half a sixteenth then stops: the pattern is detached and bouncy. At 100%, notes touch; with legato portamento they glide into each other. Gate works hand in hand with the ADSR envelope: a short gate never lets the envelope reach sustain, so only attack and decay are heard.

Latch, swing and ratchets

Latch (or Hold)

Latch keeps the chord going after you let go of the keys. The pattern runs on its own and your hands are free for the filter. A new chord replaces the old one; on some instruments, notes added while a key is still held join the current chord.

Swing

Swing delays every other note. At 50% the grid is straight; around 55 to 60% the pattern gains a more human lilt without sounding lopsided.

Ratchets and rests

Recent arpeggiators borrow sequencer features: ratchets (a note repeated two, three or four times within one step, as a burst), muted steps, or a rhythm pattern that decides which steps play. That is how you break an arpeggio’s regularity without changing its notes.

Three recipes to try

The trance pluck

  1. Up mode, two octaves, 1/16, 50% gate, latch on.
  2. Sawtooth oscillator, low-pass filter fairly closed, filter envelope with zero attack and short decay.
  3. Add a dotted-eighth delay: the repeats fill the gaps in the pattern.

The “Berlin School” sequence

  1. As-played mode, one octave, 1/16, 80% gate.
  2. Play four notes with the root first, then slowly open and close the filter by hand or with a very slow LFO.
  3. Change one note of the chord every four bars to make the line evolve.

The random texture

  1. Random mode, three octaves, 1/16T (triplets), 30% gate.
  2. Short, percussive sound, long reverb, panning modulated by an LFO.
  3. Hold a widely spaced four-note chord (fifths and fourths) to avoid clashes.

What to check when buying

  • an as-played mode, the most musical one, missing from some entry-level models;
  • MIDI clock in and out, and the option to send the arpeggiated notes to another instrument;
  • adjustable gate and swing, often buried in a menu;
  • on a polysynth, the ability to arpeggiate while keeping a sustained pad layer (split or multitimbral mode).

For the instrument’s history, the Wikipedia article on the arpeggiator traces its path from organs to 1980s synths. More sequencing guides are collected in our sequencing and arpeggios section.